OEM719 Electrical and Environmental Specifications

OEM719 Environmental Specifications

Operating Temperature

-40°C to +85°C

Storage Temperature

-55°C to +95°C

Humidity

95% non-condensing

Random Vibration

MIL-STD-810G, Method 514.6, Category 24 (20 g RMS)1

Sinusoidal Vibration

IEC 60068-2-6

Bump

ISO 9022-31-06 (25 g)

Shock

Operating

Non-operating

 

MIL-STD-810G, Method 516.6 (40 g)

MIL-STD-810G, Method 516.6 (75 g)

Acceleration, Operating

MIL-STD-810G (CH1), Method 513.7 (16 g)

OEM719 Power Requirements

Voltage

+3.3 VDC ±5%

Allowable Input Voltage Ripple

100 mV p-p maximum

Power Consumption

0.9 W typical, GPS L1 only

1.3 W typical, GPS L1/L2, GLONASS L1/L2

1.8 W typical, all constellations/all frequencies, plus L-Band

These are typical values using serial ports without interference mitigation. Values can change with the number of satellites in view, firmware version, data logging rates and features in use. Use them as a guide for what you might expect but not as absolute values.

Inrush Current

1.71 A for less than 1.5 ms (typical)

OEM719 RF Input/LNA Power Output

Antenna Connector

OEM719

MCX female, 50 Ω nominal impedance

OEM719A

Right angle, MCX female, 50 Ω nominal impedance

OEM719B

MMBX female, 50 Ω nominal impedance

Cascaded antenna
LNA gain (before receiver)

Firmware 7.04 and later

HDR disabled

+15 dB to +55 dB, 26 dB typical

HDR enabled

+20 dB to +55 dB, 30 dB typical

Firmware before 7.04

HDR disabled

+15 dB to +40 dB, 26 dB typical

HDR enabled

+20 dB to +40 dB, 30 dB typical

RF Input
Frequencies

GPS L1:

GPS L2:

GPS L5:

1575.42 MHz

1227.60 MHz

1176.45 MHz

GLONASS L1:

GLONASS L2:

GLONASS L3:

1593-1610 MHz

1237-1254 MHz

1202.025 MHz

Galileo E1:

Galileo E5a:

Galileo E5b:

Galileo E5:

Galileo E6:

1575.42 MHz

1176.45 MHz

1207.14 MHz

1191.795 MHz

1278.75 MHz

BeiDou B1I:

BeiDou B1C:

BeiDou B2I:

BeiDou B2a:

BeiDou B3I:

1561.098 MHz

1575.42 MHz

1207.14 MHz

1176.45 MHz

1268.52 MHz

L-Band:

1525 to 1560 MHz

LNA Power

+5.0 VDC ±5%, 0 mA to 200 mA (supplied by card through center conductor of RF connector).

LNA Power is generated from the 3.3 V supply input for the OEM719.

Note: Pin 1 of P1701 is not electrically connected on the OEM719. This was the external LNA power input (LNA-PWR) on the OEM615.

 

OM-20000167 v14

November 2019

Email comments to NovAtel_TPUBS@NovAtel.com

7.07.03 / OM7MR0703RN0000
PP7 07.07.04 / EP7PR0704RN0000
7.06.03 / OA7CR0603RN0000