ITDETECTCONFIG

Enable interference detection on receiver

Platform:

OEM719, OEM729, OEM7500, OEM7600, OEM7700, OEM7720, PwrPak7, CPT7, CPT7700, SMART7

This command is used to enable or disable interference detection on the receiver. It is applicable to both Spectral Analysis Detection and Statistical Analysis Detection at the same time. Detection can be enabled on all RF paths, only one RF path (L1, L2, or L5), or no RF paths. By default, only the RF paths connecting to the first antenna are enabled.

For dual antenna receivers, an ITDETECTCONFIG_1 command is used to start interference detection on only the second antenna. The interference detection results for the second antenna are shown in the ITDETECTSTATUS_1 log. An ITDETECTCONFIG command starts interference detection on only the primary antenna. The interference detection results for the primary antenna are shown in the ITDETECTSTATUS log.

The ITDETECTCONFIG and ITDETECTCONFIG_1 commands use the same message ID.

Enabling interference detection on both antennas slows down interference detection. In most installations, the primary and secondary antennas will be impacted by the same interference signal. Therefore, enabling interference detection on both antennas will slow down detection and may provide only limited benefits.

Message ID: 2143

Abbreviated ASCII syntax:

ITDETECTCONFIG RFPath [reserved1] [reserved2] [reserved3]

Factory default:

ITDETECTCONFIG all

ASCII example:

ITDETECTCONFIG L1

ITDETECTCONFIG none

Field

Field type

ASCII value

Binary value

Description

Format

Binary bytes

Binary offset

1

Command header

-

-

ITDETECTCONFIG header

This field contains the command name for abbreviated ASCII or the message header for ASCII or Binary.

-

H

0

2

RFPath

See Table: RF path selection

RF path selected for detection. By default, all paths are turned on. The receiver will cycle through all active paths.

Enum

4

H

3

reserved1

0

Reserved parameter

Ulong

4

H+4

4

reserved2

0

Reserved parameter

Ulong

4

H+8

5

reserved3

0

Reserved parameter

Ulong

4

H+12
RF path selection

Binary

ASCII

Description

0

NONE

Turn off detection on all paths

1

ALL

Turn on detection on all paths (cycle through all active paths)

2

L1

Turn on detection only on L1 path

3

L2

Turn on detection only on L2 path

4

L5

Turn on detection only on L5 path
RF paths for OEM7 receivers

RF path

OEM719, OEM729,
OEM7700, PwrPak7,
CPT7700, SMART7

OEM7720,
PwrPak7D, CPT7

OEM7500,
SMART2

OEM7600

L1

GPS L1

GLONASS L1

Galileo E1

BDS B1

QZSS L1

SBAS L1

 

GPS L1

GLONASS L1

Galileo E1

BDS B1

QZSS L1

SBAS L1

 

GPS L1

GLONASS L1

Galileo E1

BDS B1

QZSS L1

SBAS L1

LBand

GPS L1

GLONASS L1

Galileo E1

BDS B1

QZSS L1

SBAS L1

 

L2

GPS L2

GLONASS L2

Galileo E6

BDS B3

QZSS L2/L6

 

 

GPS L2/L5

GLONASS L2/L3

Galileo E5

BDS B2

QZSS L2/L5

NavIC L5

SBAS L5

GPS L2/L5

GLONASS L2/L3

Galileo E5

BDS B2

QZSS L2/L5

NavIC L5

SBAS L5

GPS L2/L5

GLONASS L2/L3

Galileo E5

BDS B2

QZSS L2/L5

NavIC L5

SBAS L5

L5

GPS L5

GLONASS L3

Galileo E5

BDS B2

QZSS L5

NavIC L5

SBAS L5

 

 

 

LBAND

LBand

LBand

 

LBand